Duration of Clinical Stages of Implant-Supported Fixed Dentures Manufacture with Screw-Retained Solid Abutments

E. V. Diiev

Abstract


The article indicates that implant-supported fixed restoration with screw-retained solid abutments is the way of prosthetic rehabilitation of patients with different dentition defects. One of the uncertain legal status reasons for this kind of orthopedic surgery is the lack of institutional regulations of time for their performing.

The objective of research was to establish time standards for an orthopedist for manufacturing of implant-supported fixed structures with screw-retained solid abutments.

Materials and methods of the research

The object of research was a clinical process of dental orthopedic care in case of implant-supported fixed structures with screw-retained solid abutments manufacturing.

Scope of research involved the structure, sequence, duration and scope of the appropriate orthopedic care.

The standard time for the manufacturing of such structures by dentist-orthopedist is determined after appropriate time and motion research as the sum of duration of each prosthetic unit manufacturing in the structure of the prosthesis according to the nature of the working time spent on its production using the formula ST = Tc + K x Tcc.

Results of the research

9 orthopedists made prosthetic appliances to 9 patients to whom 7 bridgeworks and 8 single crowns using screwed solid abutments were manufactured on 22 implants. Time and motion observations and the subsequent mathematical calculations of their work showed that the clinical process of implant-supported fixed dentures with screw-retained solid abutments manufacturing consists of 6 clinical stages during which constant time expenditure (Tc) of orthopedist constitute 165.73 minutes on any construction, and changeable-constant time expenditure (Tcc) comprises 31.24 minutes for a single crown and 47.47 minutes on bridgework with 2 foundations, therefore Tcc on 1 foundation in the prosthesis is 23.74 minute.

Thus, the time standard for the manufacture of a single crown TS = Tc + K x (Tcc) = 165.73 min + 1 x 31.24 min = 196.97 min, where K is the number of single crowns. The time standard for the manufacture of a bridgework is TS = Tc + K x Tcc of 1 foundation = 165.73 min + 2 x 23.74 min = 213.20 min, where K is the number of bridge supports.

Conclusions. Time standard of orthopedist for implant-supported single crown with a screw-retained solid abutment manufacture for a particular patient is 196.97 min, and for the manufacture of bridge with two such foundations is 213.20 min.

When manufacturing such single crown or bridgework with a different number of structural elements for one patient several, the appropriate correction coefficient (K) corresponding either to a number of single crowns or to the number of bridge foundations is required to be used.


Keywords


dental implants; screw-retained solid abutments; time and motion; standard time; dentures

Full Text:

PDF

References


Labunets VA. Fundamentals of scientific planning and organization of orthopedic dental care at the present stage of its development. Monograph. Odessa. 2006; 427.

Zablotskyi YaV, Didyk NM. Prevalence and structure of dentition defects in the population of Lviv and Lviv region. Visnyk stomatolohii. 2005; 1: 78-87.

On approval of the protocols of care in such specialties as “Prosthetic dentistry”, “Therapeutic Dentistry”, “Surgical Dentistry”, “Orthodontics”, “Paediatric Therapeutic Dentistry”, “Paediatric Therapeutic Dentistry” of 2004, Pub L. №566 (November 23, 2004).

On approval of standards of medical care and quality of medical care of 2002, Pub L. №507 (December 28, 2002).

Diiev EV, Labunets VA, Shnaider SA, Diieva TV. Topical issues of dental implantation in the context of the concept of comprehensive implant care in Ukraine. Innovatsii v stomatolohii. 2014; 2: 72-77.

Paraskevysh VA. Dental implantology: fundamentals of theory and practice. Monograph. Meditsinske informatsionnoe agenstvo. Moscow. 2011; 399.

Nespriadko VP, Kuts PV. Dental implantology. Monograph. “Kontrast”. Kharkiv. 2009; 287.

Labunets VA, Hryhorovych VR. Methodological aspects of a unified system of accounting, control work of dentists, orthopedists and dental technicians in Ukraine. Guidelines. Odesa. 1999; 12.

Diiev EV, Labunets VA, Shnaider SA, Diieva TV. Features of statistical processing of chronometry measurements of dentures manufacture duration when standardization of professionals working in dentistry. Galic’kij lìkars’kij vìsnik. 2014; 4 (21): 107-109.


Refbacks

  • There are currently no refbacks.




Copyright (c) 2016 E. V. Diiev

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.


IFNMU Logo

Free counters!